Public Notice: Sewer Main Flushing 2026 – Phase 1

Annual Sewer Main Flushing – Phase 1

Our Annual Sewer Main Flushing Program kicks off Phase 1 from August 17 to August 21. Crews will be working daily from 8:30 AM – 4:00 PM.

Streets are listed in the order they’ll be flushed each day. This schedule is tentative and subject to change depending on factors such as scheduling, main size, weather, amount of solids, access, and equipment issues.

• Day 1: Line behind civic 3-15 Crestline Rd, Park Dr (civic 119-99 odd), Crescent Dr (civic 31-39 plus 1 Crestline), Park Dr (civic 130-121, 118-126 + 3 Sail View Ln)
• Day 2: Sunset Ln (civic 1-8 + 77 Park Dr), Crestline Rd (civic 8-25), Park Dr (civic 89-95 odd), Kildare Ct Section A (civic 18-28 even, 19-15 odd)
• Day 3: Kildare Ct Section 2 (civic 16-2 even, 13-1 odd), Calistoga Rd (civic 23-9), Park Dr (civic 85-75 odd)
• Day 4: Holiday Dr (civic 38-16 + 6 Crestline Rd), Forest Rd (civic 36-16)
• Day 5: Park Dr (civic 69-53 odd), Broadway Ave (civic 38-10), Park Dr (civic 68-60 even)

Additional information on the Annual Sewer Main Flushing 👇👇👇

Why are you cleaning and inspecting the sewers?

The cleaning and inspection program keeps the sewer system operating efficiently by:

· helping prevent blockages and backups

· removing built-up debris, such as tree roots, grease, grit and sand

· determining the condition of the sewer so we can repair or replace as necessary

How do you clean the sewers?

We use a high-pressure nozzle to flush water down the sewer. The dirt and debris are sucked up through a manhole by a large vacuum truck and taken to the landfill.

Do I need to do anything before you clean/inspect the sewers on my street?

Yes. Occasionally during cleaning and inspection, air pressure in the sewer can cause water to splash out through toilets, sinks and drains. Take the following precautions to prevent water damage in your home:

· Close the lids on all toilet bowls when not in use.

· Insert drain plugs in all sinks and bathtubs when not in use.

· Remove all floor mats in bathrooms.

· Place an old towel around the base of toilets.

· If you have a float plug in your floor drain or a Backwater valve installed in your house, ensure that it is free of debris and operating properly.

· Wrap the cover of your basement floor drains with thick plastic (i.e., a freezer bag). Place something heavy over the floor drains to keep the plastic-covered floor drain covers in place.

Will I notice anything after you have cleaned/inspected the sewers on my street?

· Sometimes the sewer cleaning and inspection leaves an odour in the home. If so, run some water down the sink and bathtub drains, flush the toilets, pour a pail of water into each basement floor drain, and open the windows. After a short time, the odour should disappear.

Can I use the toilets and my water while you are cleaning and inspecting the sewer on my block?

· Yes. However, be careful as air pressure in the sewer during the cleaning and inspection can sometimes cause water to splash out through toilets, sinks and drains. Remember to close the lids on all toilet bowls when not in use, and insert drain plugs in all sinks and bathtubs when not in use.

Ways you can protect your home against sewer backup

The sewer cleaning and inspection program is one of the steps that we take to reduce the risk of sewer backup.

There are steps you can take to protect your home against basement flooding, including:

· Install a backwater valve and sump pit drainage system

· Check and maintain your backwater valve and sump pit drainage system regularly

· improve drainage around your house